Husqvarna TC 250 2011 Скачать руководство пользователя

Страница: 40 / 366

D.10

SETTINGS AND ADJUSTMENTS

Ed. 07-2010

- Remove the plates (8), lubricate the new plates with engine oil and install

them (always start with a friction plate).

Refit clutch actuator plate, bearing and pressure plate.

Tighten the spring screws gradually in a cross pattern (8 Nm - 0.8 Kgm - 5.8 ft/

lb).

When refitting the clutch cover (8 Nm - 0.8 Kgm - 5.8 ft/lb), check gasket for

wear and replace as required.

For additional information on assembly procedures, see Section "H"

Engine assembly.

Hydraulic clutch lever adjustment and fluid level check

Free play (A) must be at least 0.1 in.

The lever position can be adjusted to suit the rider hand size.

To decrease the lever distance from the handgrip, rotate the adjuster (B)

CLOCKWISE.

To increase the lever distance from the handgrip, rotate the adjuster (B) COUN

TER CLOCKWISE.

Fluid level is checked as follows:

- Remove screws (1), cover (2) and rubber diaphragm from the control;

- Keep the control cylinder (3) in a horizontal position and make sure that fluid

level has not dropped lower than 4 mm (0.16 in.) below the upper edge (D)

of master cylinder body;

- If needed, top up with the fluid specified in the LUBRICANT CHART included

in Section "A".

Refit any parts you have removed.

Periodically check the connecting hose (see “Scheduled Maintenance Chart”);

if hose (C) is worn or cracked, its replacement is advised.

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды