Husqvarna TC 250 2011 Скачать руководство пользователя страница 46

Страница: 46 / 366

D.16

��

�

��

�

H02187

SETTINGS AND ADJUSTMENTS

Ed. 07-2010

Coolant level check

Check level (1) in right-hand radiator when engine is cold (place the motorcycle

so that it is perpendicular to the ground). The coolant should be approximately

0.39 in. above the cells.

The radiator cap features two locking positions: the first one is for prior discharge

of pressure from the cooling system.

Avoid removing radiator cap when engine is hot, as coolant may spout

out and cause scalding.

TE-TXCi: Because the cooling fan (V) can be activated even when the

start switch is in OFF position, always keep at a safe distance from the

fan blades.

Difficulties may arise in eliminating coolant from painted surfaces. If this

occurs, wash off with water.

Coolant replacement

Place a vessel on the L.H. side of the cylinder, under the hose (1).

Loosen the clamp (2) on the hose (1) and detach the hose from the engine.

SLOWLY open the cap (3) of the right-hand radiator and lean the motorcycle to

the left to let the coolant drain into the vessel.

When finished, refit the hose (1) and secure it with the clamp (2).

Pour the necessary quantity of coolant in the radiator then warm up the engine

in order to eliminate any possible air bubbles.

Periodically check the connecting hoses (see “Scheduled Maintenance Chart”):

this will avoid coolant leakage and consequent engine seizure. If hoses (A) show

cracks, swelling or hardening due to sheaths desiccation, their replacement

shall be advisable.

Check the correct tightening of the clamps (B).

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Бренды по названию

Популярные бренды