Husqvarna TC 250 2011 страница 334 Скачать руководство пользователя

Страница: 334 / 366

S.4

�

��

H02330

FUEL INJECTION SYSTEM

Ed. 07-2010

a- Fuel pump retaining screw

b- Delivery fitting

c- Pump filter

d- Fuel filter

INJECTION FUEL FEEDING SYSTEM (TC)

The injection fuel feeding system is composed of fuel tank (1), electric pump

(2), pipe (3) and injector (4). The fuel in the tank is pumped by the pump. The

pressurised fuel flows into the injector installed on the throttle body (6). The

electronic control unit (5) located under the tank signals the injector to open and

a fan-shaped spray of fuel is injected into the combustion chamber.

The parameters that play a role in determining proper fuel delivery under all

operating conditions are as follows:

- Air temperature in the intake manifold;

- Engine coolant temperature;

- Atmospheric pressure in the intake manifold (in current location and at cur-

rent altitude);

- Throttle opening;

- Gear shift position;

- Fuel injection pulse width;

The "HUSQVARNA SERVICE TOOL" provides a tool to check these parameters

in the event the fuel injection malfunctions.

The electric fuel pump (2) is installed on the bottom of the tank (1) and is com-

posed of rotor, magnet, impeller, brushes, control valve and relief valve. The

electronic control unit (5) switches the pump ON/OFF.

To remove the fuel pump (2) see section “E”.

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды