Husqvarna TC 250 2011 страница 41 Скачать руководство пользователя

Страница: 41 / 366

D.11

SETTINGS AND ADJUSTMENTS

Ed. 07-2010

A: to increase clearance

B: to decrease clearance

Front brake lever adjustment and fluid level check

The adjuster (1) located on the control lever, allows adjusting of the free play

(a). Free play (a) must be at least 3 mm.

The level of the fluid in master cylinder reservoir must never be below the mini

mum value (2), which can be checked from the inspection window on the rear of

the master cylinder body. A decrease of the fluid level will let air into the system,

hence an extension of the lever stroke.

If the brake lever feels mushy when pulled, there may be air in the brake

line or the brake may be defective: CHECK THE BRAKING SYSTEM

(see Section "L").

Too much brake lever free play may reduce braking action: CHECK

BRAKE PAD THICKNESS (see Section "L").

Do not spill brake fluid onto any painted surface or lens (for example

lights lens).

Do not mix two brands of fluid. Completely change the brake fluid in the

brake system if you wish to switch to another fluid brand.

Brake fluid may cause irritation. Avoid contact with skin or eyes. In case

of contact, flush thoroughly with water and call a doctor if your eyes were

exposed.

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды