Husqvarna TC 250 2011 Скачать руководство пользователя страница 284

Страница: 284 / 366

M.22

H02311

TE-TXCi

H02360

ELECTRICAL SYSTEM

Ed. 07-2010

CHARGING SYSTEM INSPECTIONS

Current loss at the battery (TE - TXCi)

Remove the saddle (as described in the relevant paragraph) to gain access to

the battery (1).

Disconnect the BLACK negative cable from the battery.

Measure current across the negative terminal of the battery and the negative

cable using a meter. A reading greater than 1 mA indicates current loss.

If the vehicle is to remain unused for long periods, it is recom-

mended to disconnect the battery from the electrical system and

store it in a dry place.

Regulated voltage (TE - TXCi)

Remove the saddle (as described in the relevant paragraph) to gain access to

the battery.

With the engine warmed up and running at slightly above 3000 rpm, measure

voltage across the positive and negative terminal of the battery using a meter

(the battery must be charged when performing this test). If reading is outside a

12.5-14.5 V range, check generator and voltage regulator/rectifier as described

in the relevant paragraph.

Voltage regulator/rectifier inspection (TE - TXCi)

With the ignition on and the battery charged (12.5-13 V), start the engine: if bat-

tery voltage fails to rise (14 V) within the next two minutes, change the regulator

(1) as outlined in the relevant paragraph.

Voltage regulator

The voltage regulator (1) incorporates the diodes used to rectify the generator

current output.

It also incorporates an electronic device that adjusts charging voltage to battery

charge: if battery charge is low, charging voltage will be lower.

Do not disconnect the battery cables while the engine is running,

or the regulator will suffer irreparable damage.

VOLTAGE REGULATOR/RECTIFIER WIRING DIAGRAM

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Бренды по названию

Популярные бренды