Husqvarna TC 250 2011 Скачать руководство пользователя страница 321

Страница: 321 / 366

N.5

H02370

ENGINE COOLING

Ed. 07-2010

Engine cooling system overhaul (TC)

If the coolant runs too hot, check the radiators. Any foreign matter trapped

between the fins (such as leaves, bugs, mud, etc.) will obstruct air flow and

must be removed carefully to avoid damage to radiator. Straighten any bent

fins to ensure free flow of air. If the cooling mass is clogged or damaged, no

more than 20% of its surface must be affected. If damage exceeds this limit,

the radiator must be replaced. Periodically check the connecting hoses (see

Section B, “Scheduled Maintenance Chart”); this will avoid coolant leakage and

consequent engine seizure. If hoses show cracks, swelling or hardening due

to sheaths desiccation, their replacement shall be advisable. Check the correct

tightening of the clamps.

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Бренды по названию

Популярные бренды