Husqvarna TC 250 2011 Скачать руководство пользователя

Страница: 36 / 366

D.6

SETTINGS AND ADJUSTMENTS

Ed. 07-2010

Valve clearance adjustment

Remove saddle and tank as outlined in the relevant paragraphs.

Remove spark plug (1), both head cover screws (2) and head cover (3).

Engage the 2nd gear and push and pull the motorcycle back and forth to bring

the piston to Top Dead Centre. In this condition, the holes (4) in the camshaft

gears will be located at the positions shown.

Cover parting line "A" is visible through the holes (4).

Use a feeler gauge to make sure clearance is 0.15 mm on the INTAKE side and

0.20 mm on the EXHAUST side.

If not so, remove the shim from under the valve bucket and measure its thick

ness.

Depending on what you find, replace the shim with a new shim with the required

thickness to achieve correct clearance (replacement shims are available in a

1.60 mm to 2.60 mm thickness range, in 0.05 mm increments).

Check valve clearances again. If clearances are correct, refit the parts you have

removed reversing the disassembly procedure.

For camshaft disassembly and reassembly, see Section “F” Engine disassembly

and Section “H” Engine assembly.

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды