Husqvarna TC 250 2011 страница 243 Скачать руководство пользователя

Страница: 243 / 366

J.9

REAR SUSPENSION

Ed. 07-2010

Clamp the top section of the shock absorber in a vice with aluminium or bronze

jaws. Insert a rod or a screwdriver into the mounting hole and extract the rod

guide and piston assembly from the shock absorber body. Before extracting the

assembly, cover the end of the shock body with a cloth to capture leaking oil.

Keep the shock absorber in the vice taking in nearly vertical position. If

you drain the oil, you will need to replace the reservoir floating piston.

Pour the oil into a clean pan and leave it to settle.

Piston assembly inspections

1) Check the seal for wear or damage (replace if worn or damaged)

2) Check the O-ring on the rod guide. Replace if scored.

3) Check the surface of the chrome-plated rod for dents or scoring. If any dam-

age is found, seal and DU bush will be damaged as well and you will need

to replace the rod guide, too. (Rod, rod guide and clevis are supplied as a

set).

Seal replacement

If you need to replace the seal, unscrew the clevis, slide off the rod guide and fit

a new seal. Reassemble and refit the clevis securing it with Loctite and tighten

ing to 50 Nm (5 kgm; 36.9 ft/lb).

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды