Husqvarna TC 250 2011 страница 335 Скачать руководство пользователя

Страница: 335 / 366

S.5

H02374

H02375

FUEL INJECTION SYSTEM

Ed. 07-2010

Operation Manual for "HUSQVARNA SERVICE TOOL" for injection fuel

feeding system (TE-TXCi)

The injection fuel feeding system does not require scheduled maintenance

The "HUSQVARNA SERVICE TOOL" part no. 8000 H3898 lets you test system

components in the event of a malfunction.

TE = A malfunction is indicated by the word "FAIL" appearing in the right-hand

portion of the dashboard display when the ignition key is set to ON and the right

switch is set to RUN.

The "HUSQVARNA SERVICE TOOL"

is composed of:

1) "Diagnostic Tool" Software CD-ROM, including User Guide (PDF), Operation

Manual (PDF);

- User Guide hard-copy;

- Operation Manual hard-copy;

2) Diagnosis module part no. 8000H3902

3) Bike-module connection cable part no. 8000 H3899 (KEIHIN, MIKUNI

MY11)

4) Module-PC USB cable part no. 8000 H3903

5) Do not use

6) Do not use

After installing the Diagnostic Tool Software according to the instructions provided

in the User Guide, proceed as follows:

- Remove the front headlight fairing/number holder as described in the relevant

section;

- slip off the cap (B) of the ECU interface connector (C);

- connect the Kit cable (3) to the connector (C);

- Connect the USB cable (4) to the PC;

TE = Turn the ignition key (F) to ON

TXCi = Check that switch (G) is in 'RUN position';

- start the "Diagnostic Tool" software you have installed and perform the

required tests.

In case of throttle body (H) removal and/or replacement, it is ne-

cessary to carry out the T.P.S. adjustment again by selecting the

relevant option (“T.P.S. idle adjustment”).

This diagnostic software can check the following injection param-

eters:

1 - AIR TEMPERATURE (air temperature in the intake manifold);

2 - WATER TEMPERATURE (engine coolant temperature);

3 - AIR PRESSURE (atmospheric pressure in current location and at current

altitude);

4 - THROTTLE POSITION (throttle opening rate);

5 - BATTERY (battery voltage);

6 - GEAR SHIFT POSITION (currently selected gear shift position);

7 - INJECTOR (fuel injection pulse width);

8 - IGNITION COIL (device that stores energy in the reel and discharges it to

the spark plug);

9 - O2 SENSOR HEATER (heats O2 sensor up to a temperature that will

provide a stable output);

10 - O2 SENSOR (detects lean or rich mixture).

Содержание TC 250 2011















































































































































































































































































































































































Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды

Husqvarna TC 250 2011, Руководство по ремонту

Результаты поиска

Содержание TC 250 2011

Отзывы:

Похожие инструкции для TC 250 2011

Бренды по названию

Популярные бренды