Husqvarna 550H EPOS Скачать руководство пользователя

Страница: 39 / 44

Mowing

Automower

550H EPOS

Cutting system

3 pivoted cutting blades

Maximum cutting motor speed, rpm

2700

Power consumption during cutting, W +/- 20 %

Cutting height, cm / in.

5-9 / 2.0-3.6

Cutting width, cm / in.

24 / 9.4

Narrowest possible passage, m / ft.

2 / 6.5

Maximum slope for cutting area, %

Maximum slope for virtual boundary, %

Working capacity, m

/ acre(s) +/- 20%

5000 / 1.25

IP-classification

Automower

550H EPOS

Robotic lawn mower

IPX4

Charging station

IPX1

Power supply charging station

IP44

Frequency Band Support

Bluetooth

Frequency range

2400.0-2483.5 MHz

Automower

Connect 2G

GSM 850 MHz, E-GSM 900 MHz, DCS 1800 MHz, PCS 1900 MHz

Automower

Connect 4G

Band 12 (700 MHz), Band 17 (700 MHz), Band 28 (700 MHz), Band 13 (700 MHz),

Band 20 (800 MHz), Band 26 (850 MHz), Band 5 (850 MHz), Band 19 (850 MHz),

Band 8 (900 MHz), Band 4 (1700 MHz), Band 3 (1800 MHz), Band 2 (1900 MHz)

SRD915

902-928 MHz

Power Class

Bluetooth

Output power

8 dBm

Automower

Connect 2G

Power Class 4 (GSM/E-GSM)

33 dBm

Power Class 1 (DCS/PCS)

30 dBm

Power Class E2 (GSM/E-GSM)

27 dBm

Power Class E2 (DCS/PCS)

26 dBm

Automower

Connect 4G

Power Class 3

23 dBm

SRD915

13 dBm

Full compatibility cannot be guaranteed between the product and other types of wireless systems such as remote

controls, radio transmitters, hearing loops, buried electric animal fencing or similar.
The products are made in England or the Czech Republic. See information on the rating plate. Refer to

Product

overview on page 5

8.2 Registered trademarks

The

Bluetooth

word mark and logos are registered trademarks owned by

Bluetooth SIG, inc.

and any use of such

marks by Husqvarna is under license.

1619 - 002 - 19.01.2021

Technical data - 39

Содержание 550H EPOS












































Результаты поиска

Содержание 550H EPOS

Отзывы:

Похожие инструкции для 550H EPOS

Бренды по названию

Популярные бренды

Husqvarna 550H EPOS, Руководство оператора

Результаты поиска

Содержание 550H EPOS

Отзывы:

Похожие инструкции для 550H EPOS

Бренды по названию

Популярные бренды