Husqvarna 550H EPOS Скачать руководство пользователя страница 34

Страница: 34 / 44

6.4 LED indicator lamp on the charging station

For a fully functional installation, the indicator lamp in the charging station must show a solid or flashing green light. If

another color shows, follow the troubleshooting guide below.
There is more help on www.husqvarna.com. If you still need help, speak to your local Husqvarna representative.

Light

Status

Green solid light

Good signals.

Green flashing light

The signals are good and

ECO mode

is activated. Refer to

ECO mode on page 21

Red flashing light

Interruption in the charging station’s antenna. Speak to your local Husqvarna repre-

sentative.

Red solid light

Fault in the circuit board or incorrect power supply in the charging station. The fault

must be correct by an authorized service technician. Speak to your local Husqvarna

representative.

6.5 LED indicator lamp on the product

The LED indicator lamp on top of the product shows the current status:

Light

Status

Green solid light

The product is mowing the lawn or leaving the charging station.

Green flashing light

The product is paused.

Red flashing light

The product has stopped due to an error.

Yellow solid light

The STOP button has been pushed.

Yellow flashing light

The product requests the PIN code.

Blue solid light

The product is on its way to the charging station or a point of interest.

An app is connected to the product with Bluetooth

, the blue solid light is lit for 3

seconds.

Blue pulsating light

The product is charging in the charging station.

Blue flashing light

The product is parked in charging station.

The product can at this time find the Bluetooth

to connect with.

White solid light

The product is in appDrive mode.

White pulsating light

The product switching off.

Firmware installation is ongoing.

White flashing light

The firmware must be updated.

There is more help on www.husqvarna.com. If you still need help, speak to your local Husqvarna representative.

34 - Troubleshooting

1619 - 002 - 19.01.2021

Содержание 550H EPOS












































Результаты поиска

Содержание 550H EPOS

Отзывы:

Husqvarna 550H EPOS, Руководство оператора, Страница: 34 / 44

Результаты поиска

Содержание 550H EPOS

Отзывы: