Husqvarna 550H EPOS Скачать руководство пользователя страница 33

Страница: 33 / 44

6.3 Information and warning messages

The information messages in the table below are shown in the

Messages

menu in the Automower

Connect app.

Speak to your Husqvarna representative if the same message shows frequently.

Message

Cause

Action

Low battery

The product cannot find the charging sta-

tion.

The product has no accurate position

and cannot find the charging station.

There is an obstacle preventing the prod-

uct to find the charging station.

The battery is at the end of its life cycle.

Replace the battery. Refer to

Battery on

page 26

The charging station’s antenna is defec-

tive.

Check if the indicator lamp in the charg-

ing station flashes red. Refer to

LED indi-

cator lamp on the charging station on

page 34

. This problem requires action

by authorized service technician.

Cutting system imbalance

The product has discovered vibrations in

the cutting disc.

Make sure that the blades and screws

are not damaged and not worn. Make

sure that all blades are correctly attach-

ed. Make sure that there is only one

blade attached in each position on the

blade disc.

Connectivity problems

Problem with the Automower

Connect

module.

Restart the product. If there still is a con-

nection problem, try to unpair the product

(My mowers)

and then pair it again. If the

problem remains, speak to your local

Husqvarna representative.

Wrong PIN code

An incorrect PIN code has been entered.

5 tries are permitted, and the product is

then blocked for a period of time.

Enter the correct PIN code. If the PIN

code is incorrect, use the link in the app

to send the PIN code to your registered

e-mail address. If you have not regis-

tered the e-mail address, speak to your

local Husqvarna representative.

Ultrasonic problem

Temporary electronic or firmware related

issue in the product.

Restart the product.

If the problem stays, speak to your ap-

proved servicing dealer.

GPS navigation problem

1619 - 002 - 19.01.2021

Troubleshooting - 33

Содержание 550H EPOS












































Результаты поиска

Содержание 550H EPOS

Отзывы:

Husqvarna 550H EPOS, Руководство оператора, Страница: 33 / 44

Результаты поиска

Содержание 550H EPOS

Отзывы: