manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 9 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 9

b.3

Part. N. 8000 H0368 (09-2008)

IMPORTANT NOTICES

* This motorcycles was not designed for long trips with the engine
always at maximum rpm as can occur whilst travelling on roads
or highways. Long trips at full throttle can cause severe damage
to the engine.

* This motorcycles is setup for competition use and therefore guar-
antees maximum performance with the rider alone. It is thereby
not recommended to use the vehicle on circuits or off-road with a
passenger.

* ALWAYS keep in mind that these motorcycles have been de-
signed strictly for competition use, that is, for conditions of usage
very different from those presented on the road.

* In order to maintain the vehicle’s “Guarantee of Functionality”,
the client must follow the maintenance program indicated in the
chapter B by carrying out maintenance checks at authorized
HUSQVARNA dealers. The cost for substituting parts and for the
labour necessary in order to respect the maintenance plan, is
charged to the client. The guarantee is EXTINGUISHED in the
case where the motorcycle is rented.

Notes
References to the “left” or “right” of the motorcycle are in the sense
of a person facing forwards.

Z: number of teeth

A: Austria
AUS: Australia
B: Belgium
BR: Brazil
CDN: Canada
CH: Switzerland
D: Germany
E: Spain
F: France
FIN: Finland
GB: Great Britain
I: Italy
J: Japan
USA: United States of America
Where not specified, alla the data and the instructions are re-
ferred to any and all the Countries.

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов