manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 263 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 263

L.5

Part. N. 8000 H0368 (09-2008)

BRAKES

Wear check and replacement of brake pads

Inspect pads for wear.
Service limit “ A”

TE, TC, TXC

- 3,8 mm-0.15 in. (front and rear pads)
If service limit is exceeded, always replace the pads in pairs.

SMR

a) In front: thickness “A” must never be lower than the one pointed out by the wear
control notches.
b) At the back: thickness “A” must never be lower than 3,8 mm-0.15 in.
If service limit is exceeded, always replace the pads in pairs.
Be careful that no disc brake fluid or any oil gets on brake pads or discs. Clean off
any fluid or oil that inadverently gets on the pads or disc with alcohol.
Replace the pads with new ones if they cannot be cleaned satisfactorily.
PADS REMOVAL
-Remove springs (1).
-Remove pins (2).
-Remove pads.
PADS INSTALLATION
- Install new brake pads.
- Reassemble the two pins (2) and the springs (1).
If the above procedure is followed it will not be necessary to bleed the brake system
after new pads have been fitted.
Pumping the brake lever several times is sufficient to return the pistons to their
normal position.

 During the operation of pads replacement, it is advisable to remove a small

quantity of fluid from reservoir, since piston backing inside cylinders could cause
overflowing of fluid from reservoir.

FRONT

REAR

2

1

1

2

FRONT

REAR

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов