manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 209 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 209

I.19

Part. N. 8000 H0368 (09-2008)

FRONT SUSPENSION

6

2

2

3

8

2

7

2

9

2

F

• Insert the foot buffer push rod ( 29 ) into the rod ( 32 ); this must be done in a way
that the spanner seizing side is oriented towards the
body ( 30 ) and the metal ring seat ( F ) is
exceeded.

• Insert the metal ring ( 27 ) into the proper seat( F )

• Bring the push rod ( 29 ) into contact with the stop ring.

• Insert the foot buffer ( 28 ); this must be inserted keeping the oil flow slots towards
the push rod.

• Insert the upper nut ( 26 ) and tighten it on the push rod ( 29 ).

• Hold the nut ( 26 ) with a 18 mm spanner and tighten the push rod ( 29 ) up to the
required torque (see Table 1 - Tightening Torques), using a 17 mm spanner.

• Insert the guide spring ( 24 ) in the pumping element rod ( 32 ); the guide spring
must have the smaller diameter side towards the foot buffer.

• Screw the locknut ( 23 ) till the end without tightening.

6

2

9

2

3

2

4

2

2

3

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов