manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 372 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 372

P.4

Part. N. 8000 H0368 (09-2008)

HYDRAULIC CONTROL CLUTCH

Discharge of hydraulic system fluid

Connect a small plastic hose to the discharge valve and unscrew it by one or two
turns. Remove the reservoir cover and the diaphragm and act release control
lever until all fluid is discharged.

Overhaul of the control pump for clutch release

Drain the system, detach the pump from the L.H. side of the handlebar and
disassemble the pump completely. Replace all gaskets, re-assemble the pump
and assemble it again on the handlebar. Connect the hose and pour new fluid
from the tank; bleed the system as shown on page P.5.

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов