manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту

Husqvarna 2009 TE 250 - отличный мотоцикл для экстремальных поездок. Для тех, кто хочет узнать больше о мощности и возможностях этой модели, предлагаем скачать Workshop Manual бесплатно с сайта manualshive.com, чтобы всегда быть готовым к приключениям на дороге.

Поделиться
Скачать
background image

A.6

Part. N. 8000 H0368 (09-2008)

GENERAL

FRAME
Steel single tube cradle (round, rectangular and ellipsoidal tubes, branching off into two parts approximately at the exhaust level), rear frame
in light alloy
Forward travel (in.) .............................................................. 4.17 (TE-TXC); 4.10 (TC); 3.27 (SMR)

SUSPENSIONS
Front
“MARZOCCHI” Overturned forkrod telehydraulic fork with advanced pin; forkrods 1.97 in. diameter; hydraulic brake adjustment both in
compression and extension
Axle travel on leg axis (in.) .................................................. 11.81 (TE, TC, TXC); 9.84 (SMR)

Rear
Swinging arm in light alloy with progressive damping, “SACHS” hydraulic mono-shock absorber with helical spring.
Hydraulic brake and spring preloading adjustment both in compression (DOUBLE) and in extension.
Wheel travel (in.) ................................................................. 11.65 (TC-TXC-TE); 11.41 (SMR)

BRAKES
Front
Drilled fixed disc 10.24 in. dia. “wave” type, with floating caliper (TE, TC, TXC); drilled floating disc 12.6 in. dia. (SMR) with radial fixed caliper
Pads area ........................................................................... 5.18 sq. in. (TE, TC); 6.48 sq. in. (SMR)
Independent hydraulic circuit and pump with control on the handlebar right side
Rear
Floating drilled disc 9.45 in. (“wave” type for TE and TC), with floating caliper
Pads area ........................................................................... 3.64 sq. in.
Independent hydraulic circuit; controlled by pedal and pump on the motorcycle right side.

WHEELS
Rims
Front (TE, TC, TXC) ........................................................... "TAKASAGO“ Excel in light alloy: 1.6x21”
Front (SMR) ....................................................................... "SANREMO" in light alloy: 3.50x17”
Rear (TE, TXC) .................................................................. "TAKASAGO“ Excel in light alloy: 2.15x18”
Rear (TC) ........................................................................... "TAKASAGO“ Excel in light alloy: 1.85x19”(250); 2.15x19”(450-510)
Rear (SMR) ........................................................................ "SANREMO" in light alloy: 4.25x17”

TIRES
Front
(TE-TXC) ........................................ "Michelin" ENDURO COMP. 3 - "Pirelli" MT 83 Scorpion - "Dunlop" 54R-D907; 90/90x21"
(TC) ................................................ "Pirelli" 51R-MT 32A; 80/100 x 21”
(SMR) ............................................. "Pirelli" MTR 21 DRAGON-EVO; 120/70-17”
Rear
(TE-TXC) ......... "Michelin" ENDURO COMP. 3 - "Pirelli" MT 83 Scorpion - "Dunlop" 70R-D907; 120/90x18” (250); 140/80x18” (450-510)
(TC) ................. "Pirelli" NHS (62) MT 32; 100/90x19” (250); 110/90x19” (450-510)
(SMR) .............. "Pirelli" MTR 22 DRAGON-EVO; 150/60x17”

Cold tire pressure (front TE-TXC racing use, TC) .......................... 0.9÷1.0 Kg/cm

2 

(12.8-14.2 psi)

Cold tire pressure (rear TE-TXC racing use, TC) ........................... 0.8÷0.9 Kg/cm

2 

(11.4-12.8 psi)

Cold tire pressure (front TE-TXC road use) ................................... 1.1 Kg/cm

2 

(15.6 psi)

Cold tire pressure (rearTE-TXC road use) ..................................... 1.0 Kg/cm

2 

(14.2 psi)

Cold tire pressure
(front SMR) ............................................................. 1.4 kg/cm

2 

- 20 p.s.i.(Racing use); 1.8 kg/cm

2 

- 25.6

 

p.s.i. (Road use: rider only);

2.0 kg/cm

2 

- 28.4

 

p.s.i.

 

(Road use: rider and passenger)

Pressione di gonfiaggio a freddo
(rear SMR) .............................................................. 1.6 kg/cm

2 

- 22.7

 

p.s.i.

 

(Racing use); 2.0 kg/cm

2 

- 28.4

 

p.s.i.

 

(Road use: rider only);

2.2 kg/cm

2 

- 31.3

 

p.s.i.

  

(Road use: rider and passenger)

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 TE 250

Öhlins YA919 Mounting Instructions preview
YA919
Бренд: Öhlins Страницы: 2
hepco & becker 410999 00 01 Quick Start Manual preview
410999 00 01
Бренд: hepco & becker Страницы: 2
KTM Freeride E-XC 2019 Setup Instructions preview
Freeride E-XC 2019
Бренд: KTM Страницы: 44
MOTO GUZZI California EV V1100 Service Station Manual preview
California EV V1100
Бренд: MOTO GUZZI Страницы: 173
Yamaha XS650SE Shop Manual preview
XS650SE
Бренд: Yamaha Страницы: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Бренд: Yamaha Страницы: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Бренд: Yamaha Страницы: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Бренд: Yamaha Страницы: 94
HJC FG-ST Owner'S Manual preview
FG-ST
Бренд: HJC Страницы: 9
DYNATEK D3K1-4 Installation Instructions preview
D3K1-4
Бренд: DYNATEK Страницы: 3
DYNATEK D2K-HD1 User Instructions preview
D2K-HD1
Бренд: DYNATEK Страницы: 8
SCHUBERTH F300 Manual preview
F300
Бренд: SCHUBERTH Страницы: 43
hepco & becker 5039515 00 05 Quick Start Manual preview
5039515 00 05
Бренд: hepco & becker Страницы: 3
hepco & becker 506554 00 01 Quick Start Manual preview
506554 00 01
Бренд: hepco & becker Страницы: 2
JETPRIME JP MJ 008 Installation Manual preview
JP MJ 008
Бренд: JETPRIME Страницы: 4
Oxford Aqua Series Manuallines preview
Aqua Series
Бренд: Oxford Страницы: 28
R&G FI0077BK Fitting Instructions preview
FI0077BK
Бренд: R&G Страницы: 4
R&G FI0074BK Fitting Instructions preview
FI0074BK
Бренд: R&G Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды