manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 405 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 405

Y.9

Part. N. 8000 H0368 (09-2008)

FRAME AND WHEELS

Tighten the screw (3) on the fork L.H. side but DO NOT lock it. Now, pump for a while,
pushing the handlebar downwards until you are sure that the fork legs are perfectly
aligned.  Lock: the screws (1) on the R.H. leg  (10,4 Nm/ 1,05 Kgm/ 7.7 ft-lb), the
screw (3) on the L.H. side (51,45 Nm/ 5,25 Kgm/ 38 ft-lb), the screws (1) on the L.H.
leg  (10,4 Nm/ 1,05 Kgm/ 7.7 ft-lb).

SMR: fit the brake caliper on the disc; assemble the caliper on its holding plate and
tighten the screws (A) at 25,5 Nm/ 2,6 Kgm/ 18.8 ft-lb.
Check that the brake disc slides between the caliper pads without any friction.
Check the distance between magnet on the brake disc and sensor on the brake
caliper (page I. 61).

 After reassembly, pump the brake control lever until the pads are against

the brake disc.

TE-TC-TXC

1

3

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов