Husqvarna 2009 TE 250 страница 232 Скачать руководство пользователя | Manualshive

Страница: 232 / 412

background image

I.42

Part. N. 8000 H0368 (09-2008)

FRONT SUSPENSION

RE-ASSEMBLING THE FORK LEG - SLIDER AND SEALING RINGS

WARNING

The old sealing rings and dust seals must not be used again. Before re-
assembling, check the conditions of the guide bushings; replace them if they
are scratched or grooved. Check the Teﬂon® coating of the guide bushings
which must be in a good condition.

Apply some adhesive tape to the end of the stanchion tube so that it covers the seat
of the top bushing.

Smear the dust seal and the sealing ring with some grease.

• Insert the following components in the stanchion tube in this order: dust seal (16),
stop ring (15), sealing ring (14), spring cup (13) and bottom guide bushing (12).

WARNING

Make sure the sealing ring (14) is correctly oriented in a way that the hollow
side is turned towards the spring

Remove the adhesive tape from the end of the stanchion tube, cleaning any traces
of adhesive left on the fork.

Insert the top guide bushing (12) by hand.

If this operation is difﬁcult by hand, use a ﬂat-tip screwdriver in the bushing

groove.

Delicately introduce the stanchion tube into the slider, being very careful not to
damage the top guide bushing.

Guide the bottom guide bushing until it comes into contact with the slider, the spring
cup and the sealing ring.

Mount the special introducer on the stanchion tube (44) and use this, by pushing on
the sealing ring (14), to insert the bottom guide bushing, the spring cup and the
sealing ring.

15

14

13

12

16

12

14

44

«
...
230
231
232
233
234
...
»

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 TE 250

Бренд: Bajaj Auto Страницы: 38

SEMIFARINGS ANARCHY

Бренд: CUSTOMACCES Страницы: 2

Бренд: WangYe Страницы: 19

Бренд: Suzuki Страницы: 440

Бренд: Yoshimura Страницы: 4

Бренд: paladin Страницы: 2

Бренд: hepco & becker Страницы: 3

HPS.08.473.10000/B

Бренд: SW-Motech Страницы: 4

Бренд: Leatt Страницы: 23

Бренд: hepco & becker Страницы: 3

Бренд: hepco & becker Страницы: 4

Бренд: HJC Страницы: 9

Бренд: Bosch Страницы: 160

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды