manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 228 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 228

I.38

Part. N. 8000 H0368 (09-2008)

FRONT SUSPENSION

R5155

21

3

25

21

23

25

25

35

27

24

25

RE-ASSEMBLING THE CARTRIDGE UNIT

• Insert the spring (23) in its seat on the rod.

• Apply some stretched adhesive tape onto the end of the rod (39) in order to cover
the rod threading. Do not apply thick adhesive tape.

• Grease the rod and lubricate the sealing rings.

• Insert the piston rod (25) into the sleeve (35).

In both pumping elements there is a sealing segment; before re-assembling
make sure that it is not worn or damaged. Replace if necessary. Take great

care and if necessary use a small flat-tip screwdriver to help the piston of the
pumping element into the pumping element tube-sleeve. Insert the piston

without any interference.

• Remove the adhesive tape from the rod’s upper edge (25).

• Rotate the rebound adjuster in fully closed position (rotate it fully clockwise).

• Tighten by hand the locknut (27) and the rebound adjustment set (24) into the rod
threaded area (25).

• Fix the rebound adjuster set (24) with a 17 mm spanner and screw the locknut (27)
with another 17 mm spanner to the required torque (see Table 5 – Tightening
torques).

• Fix the cartridge set (21) in the vice by means of the special protection jaws (R5155),
as shown in the figure.

• Set the rebound adjuster (3) to 15 clicks from fully closed position.

• Pull the pumping element rod (25) completely in the configuration of maximum
extension.

• Fill the cartridge case (21) with oil to about 20 mm from the upper edge.

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов