manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 4 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 4

a.2

Part. N. 8000 H0368 (09-2008)

FOREWORD, SUMMARY

Foreword

This publication intended for 

HUSQVARNA 

Workshops has been prepared for the

purpose of helping the authorized personnel in the maintenance and repair work of the
motorcycles herewith dealt with. The perfect knowledge of the technical data contained
herein is essential for a more complete professional training of the operator.
The paragraphs have been completed with schematic illustrations evidencing the subject
concerned, in order to enable a more immediate understanding.
This manual contains information with particular meanings:

Accident prevention rules for the operator and for the personnel working near by.

Possibility of damaging the vehicle and/or its components.

Additional information concerning the operation under way.

Useful suggestions

HUSQVARNA suggests, in order to prevent troubles and in order to have an excellent final
result, to generically comply with the following instructions:
– in case of repair work, weigh the impressions of the Customer who complains about the

improper operation of the motorcycle, and formulate proper clearing questions about the
symptoms of the trouble.

– detect clearly the cause of the trouble. This manual gives the theoretical bases which

however shall be integrated by the personal experience and by the attendance to training
courses periodically organized by 

HUSQVARNA

.

– rationally plan the repair work in order to prevent dead time as for instance procurement

of spare parts, tool preparation, etc.

– reach the component to be repaired and perform only the required operations.

In this connection, it will be useful to consult the disassembly sequence contained in this
manual.

General instructions for repair work

1 Always replace the seal rings and split pins with new components.
2 When loosening or tightening nuts or bolts, always start from the bigger ones or from the

center. Lock at the prescribed torque wrench setting following a crossed run.

3 Always earmark the components or positions which could be mistaken one for another

at the time of assembly.

4 Use original 

HUSQVARNA 

spare parts and the lubricants of the recommended brands.

5 Use special tools, where specified.
6 Consult the Service Bulletins as they may contain up-dated adjustment data and repair

methodologies.

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов