manualshive.com logo in svg

Husqvarna 2009 TE 250, Руководство по ремонту, Страница: 244 / 412

Поделиться
Скачать
Husqvarna 2009 TE 250 Скачать руководство пользователя страница 244

J.4

Part. N. 8000 H0368 (09-2008)

REAR SUSPENSION

Removing the rear shock absorber

Remove the saddle, the side panels and the silencer as described in chapter "E’"-
General operations (pages E.15-E.16-E.17). Loosen the front clamp (1) of the

fitting on the carburettor (TC-TXC-SMR 450 R) or on the throttle body (TE-SMR).

2

4

7

3

8

5

1

9

Loosen the upper fastening screw (2) of the rear frame (4), remove the lower
fastening screw (3) and turn the rear frame forward making sure not to damage
electric cables. Remove the front fixing pin (5) of the suspension tie rod on the
frame, the lower fastening screw (6) of the shock absorber, the upper fastening

screw (7) and then remove the shock absorber (8).

IMPORTANT: when reassembling, place the lower locking nut (9) of the shock

absorber on the LEFT SIDE.

6

Содержание 2009 TE 250





























































































































































































































































































































































































































Отзывы:

Нет отзывов