Hunter ACC-1200 Скачать руководство пользователя | Manualshive

Страница: 34 / 100

background image

27

5. If the flow sensor selection has been changed to

NONE after learning, the display will show FLOW
NOT MONITORED. The actual flow may still be
viewed, even if all stations have been set to Not
Monitored. Station level alarm diagnostics would
not be available, but the flow will be visible.

Step 3: Preparing for Flow Learning

1. ACC will only learn flows for stations which have

run times in Automatic Programs. Verify that each
station has a run time in an Automatic Program (A
through F).

2. ACC can be taught to ignore flow monitoring for

stations which operate non-irrigation devices.

3. Turn the dial to another position, then hold the

Information button while turning back to the Set
Flow Monitoring position.

4. Select Edit Learned Flow (even if no flow has been

learned, yet).

5. Use the – button to set the non-irrigation stations to

Not Monitored. Use the up and down arrow buttons
to advance through the stations, and set any stations
necessary to the Not Monitored setting.

Step 4: Learning the Flow

1. Turn the dial back to the RUN position.
2. Press the LEARN button. The screen will display that

the controller will run the stations and it will also ask
you to confirm that you want to begin watering to
learn flow.

3. The ACC will begin watering at the lowest station

number to learn its typical flow. Normally this will be
station 01, unless it is Not Monitored or has no run
time in any programs.

It will run the station for a minimum of 15 seconds, and
then begin sampling flow at 5-second intervals until flow
has stabilized (at least 4 readings, 5 seconds apart, within
a reasonable flow range of one another). It will then store
the average flow for this station in its memory, and move
on to the next station. It will continue in this manner
through all stations which have at least one run time in
one of the Automatic Programs, and which are not set to
Not Monitored in the Set Flow Monitoring station settings.

Only stations with a run time in an Automatic Program
will be learned. Stations which are not programmed in any
Programs will not be sampled, and should be set to Not
Monitored to ensure proper operation of the flow meter.

If the station Delay setting has been changed, the controller
will run the station for Delay period (instead of the 15
second minimum) before sampling and learning flow.

«
...
32
33
34
35
36
...
»

Содержание ACC-1200





































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-1200

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

Бренд: Eaton Страницы: 100

Бренд: Voltech Страницы: 8

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 340

Бренд: ETC Страницы: 8

Бренд: Texas Instruments Страницы: 27

Бренд: WAGNER Страницы: 128

Бренд: K&K Страницы: 10

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: C-TEC Страницы: 28

Бренд: Zander Aachen Страницы: 75

DX99N9X1S2N0M2X0D2

Бренд: Banner Страницы: 13

Бренд: wattstopper Страницы: 4

Бренд: Gioteck Страницы: 16

X-Series X-SMS V2

Бренд: IDS Страницы: 2

Бренд: Larco Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды