Hunter ACC-1200 Скачать руководство пользователя | Manualshive

Страница: 13 / 100

background image

6

Location Requirement: A) a switch or circuit-breaker
shall be included in building installations; B) the switch
or breaker shall be in close proximity to the controller,
and within easy reach of the operator; C) the switch or
breaker shall be marked as the disconnecting device for
the controller.

2" Conduit Nut

2" Conduit Nipple

Mounting Plate

½" Conduit Nut

½" Conduit Nut

¾" Washer (4)

³∕

8

" Mounting Nut (8)

³∕

8

" Mounting Bolt (8)

Installing the Pedestal

1. Assemble the mounting template using the

instructions provided with the pedestal.

2. Using the enclosed mounting template, locate the

bolts two inches deep in the concrete pad, in the
locations indicated. The pad can be any size but at
least a two-foot square is recommended.

meTal CabIneT opTIonal pedesTal InsTallaTIon .....................

Select a location for installation of the controller based
upon these factors:

1. Availability of 120/230 VAC~ power.
2. Do not locate under overhanging branches of trees

or any structure that may attract lightning.

3. Avoid locations where sprinklers spray upward onto

the controller, and low areas subject to flooding.

4. Locate controller in a location that is central to all

valves/sprinklers that it controls to maintain visible
operation and reduce wire
lengths/costs.

3. Level the mounting bolts before the concrete sets.
4. After the concrete sets, remove the door of the

pedestal and slide the pedestal down onto the four
bolts. Secure the pedestal to the bolts using the
enclosed washers and nuts.

5. Remove the door and faceplate of the ACC and

attach the metal cabinet of the ACC to the top of the
pedestal using the ½" (13 mm) and 2" (50 mm) metal
conduit nuts in the pedestal. Tighten securely by
engaging teeth with a screwdriver and tapping in a
clockwise direction.

COnneCtInG the MetAl PeDeStAl MAIn AC POWer

1. Connect AC power wiring as in the metal wall

cabinet. Route the AC power wiring through
the metal pedestal and up into the ACC wiring
compartment. Follow the AC wiring instructions for
the metal wall cabinet closely.

2. Replace the pedestal door first and then replace the

faceplate and the cabinet door. The pedestal door
cannot be removed or replaced when the cabinet
door is closed.

Refer to Earth Ground and Station Wiring sections for
additional connections.

Conduit Nuts

plasTIC pedesTal InsTallaTIon .................................................

AC Power Wire S/P

(3" Max Above Concrete)

GCBL Wiring (Required for IMMS)

(3" Max Above Concrete)

Field Wiring

(3" Max Above Concrete)

Thread Length 2.50" Min

Above Concrete

Template

5.00"

12.50"

26" Min

21" Min

4"

«
...
11
12
13
14
15
...
»

Содержание ACC-1200





































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-1200

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Barco Страницы: 6

Бренд: Ebyte Страницы: 35

Бренд: LAS Страницы: 6

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 98

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 54

Бренд: Neets Страницы: 12

Бренд: National Instruments Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды