Hunter ACC-1200 Скачать руководство пользователя

Страница: 92 / 100

Alarm Log, “Reason” Labels

The Reason label indicates the type of alarm condition.

Unknown

No reason specified

Overflow

Overflow alarm occurred

Underflow

Underflow alarm occurred

Overcurrent

Station Overloaded

Activated

Sensor Activated

Deactivated

Sensor Deactivated

Damaged

Decoder is damaged (continuous low
voltage output)

Comm Fail

Decoder communications failure - no
response

Unavailable

Cannot run station due to too many
stations already running

Comm Restore

Communications was restored to a
decoder

Config Fail

Failure occurred when attempting to
configure a sensor decoder on the
2-wire path

Flow Totals

Failure occurred when attempting
to get the flow totals from a sensor
decoder

Flow Detail

Failure occurred when attempting to
get the flow detail data from a sensor
decoder

Sensor Alarm

The status of the Sensor Decoder
Alarm Polling has changed

Lith Fail

The lithium battery in the facepack
has failed

Clock Fail

A problem exists with the Real Time
Clock (RTC) in the facepack

COntrOller lOGS

Track significant events at the controller, which are not
necessarily alarms or malfunctions.

Message

Description

EASY RETRIEVE
RESTORED

Easy retrieve programs
were restored

PROGRAM X RESET BY
CENTRAL

Field controller Program X
was reset by central

OFF MODE SET AT
CONTROLLER

Dial was put in OFF
position

RUN MODE SET AT
CONTROLLER

Dial was taken out of OFF
position

PROGRAMMABLE OFF SET
AT CONTROLLER

Programmable Off was
initiated at the controller

PAUSE MODE SET AT
CONTROLLER

Pause Mode was initiated
at the controller

PAUSE MODE CANCELLED
AT CONTROLLER

Pause Mode was cancelled
at the controller

PROGAMMABLE OFF SET
BY CENTRAL

Programmable Off was
initiated by central

PAUSE MODE SET BY
CENTRAL

Pause Mode was initiated
by central

PAUSE MODE CANCELLED
BY CENTRAL

Pause Mode was cancelled
by central

SUSPEND MODE SET BY
CENTRAL

Suspend Mode was
initiated by central

SUSPEND MODE
CANCELLED BY CENTRAL

Suspend Mode was
cancelled by central

PROGRAMMABLE OFF
TIMEOUT

Programmable Off timed
out

PAUSE TIMEOUT

Pause timed out

NO WATER WINDOW
VIOLATION

A No Water Window
Violation occurred

MEMORY CORRUPTED
RESET TO DEFAULTS

Memory is suspect and
was reset to defaults by
microcontroller

ALL DATA RESET TO
DEFAULTS

All data was reset in the
controller

ALL LOGS RESET AT
CONTROLLER

All logs were reset at the
controller

FLOW TOTALS RESET AT
CONTROLLER

All flow totals were reset at
the controller

ALL PROGRAM DATA
RESET AT CONTROLLER

All programs were reset at
the controller

ALL NAMES RESET AT
CONTROLLER

All names were reset at the
controller

IRRIGATION STOPPED BY
CENTRAL

Irrigation was stopped by
the central

Содержание ACC-1200





































































































Результаты поиска

Содержание ACC-1200

Отзывы:

Похожие инструкции для ACC-1200

Бренды по названию

Популярные бренды

Hunter ACC-1200, Руководство пользователя

Результаты поиска

Содержание ACC-1200

Отзывы:

Похожие инструкции для ACC-1200

Бренды по названию

Популярные бренды