manualshive.com logo in svg

Hunter ACC-1200, Руководство пользователя, Страница: 21 / 100

Поделиться
Скачать
Hunter ACC-1200 Скачать руководство пользователя страница 21

14

ConneCTInG The masTer ValVe(s) and/or pump sTarT relay(s) 

The Pump/Master valve connections are located in the 
upper right of the Master Module, which is in the upper left 
corner of the controller itself.

Locate the P/M1 and P/M2 screw terminals on the Master 
Module. These outputs are designed to supply 24 VAC, 
0.320 A max, for a single Master Valve solenoid or a Pump 
Start Relay (or Relay Booster).

The return wire from each P/M device (solenoid or relay) 
must be connected to one of the COM terminals on the 
lower terminal strip of the Master Module.

Connect one output wire from each Pump relay or Master 
Valve solenoid to the desired 24 VAC P/M terminal.

Connect the return wire to one of the terminals marked 
COM immediately below the P/M outputs.

Configuration of the P/M terminals is covered in the 
Set Pump Operation section of the Programming and 
Operations portion of this manual.

Up to 4 Hunter sensors can be connected to the ACC 
controller, including:

•  Mini-Clik

®

•  Rain-Clik

™

 (including Wireless Rain Clik)

•  Freeze-Clik

®

•  Mini-weather station

Hunter Flow-Clik

™

 can also be connected, but it is 

recommended that the HFS be used instead.

In the ACC controller, Clik sensors shut down individual 
programs, not necessarily the entire controller. Each 
sensor can be given its own response instructions by 
program.

Hunter Clik sensors are usually normally closed, and open 
on alarm. This signals the controller to suspend irrigation. 
Other dry contact closure sensors can be used without 
warranty, provided that a.) they require no voltage; and 
b.) open the circuit when a shutdown condition is sensed. 
Hunter makes no claims or representations that such 
connections will be effective.

1.  To connect Clik sensors, locate the SEN [1-4] 

terminals on the Master Module (upper right corner 
of controller).

2.  Route the pair of wires from each sensor into the 

cabinet through one of the low voltage conduit 
openings in the bottom of the enclosure.

24 VaC TesT TermInal ................................................................

The Master Module features a “constant-hot” 24 VAC 
output which can be used as a test point for locating 
valves in the field:

1.  After powering up the controller, attach the common 

wire to the COM terminals as described above. 

2.  Touch each wire to the terminal marked 24 VAC to 

identify the valve location. 

3.  Each valve will open electrically when the wire is 

touched to the 24 VAC terminal. 

4.  After identifying the valve location, you may then 

insert the wire into the appropriate terminal. This 
feature allows you to sequence the valves in the 
most logical order for the user without damaging the 
controller by “sparking” the wires.

5.  The 24 VAC terminal may also be used to power 

wireless Clik sensor receivers.

 See Connecting a 

Rain Or Freeze Shut Off Device on page 14 for more 

information.

.

ConneCTInG a raIn or freeze shuT off deVICe .......................

Содержание ACC-1200





































































































Отзывы:

Нет отзывов