Hunter ACC-1200 Скачать руководство пользователя | Manualshive

Страница: 69 / 100

background image

62

address or the sensor selections at anytime, if
changes occur to the system.

• Turn the dial to “Set Sensor Operation.” There

is a display page for each Program, allowing
the responses for each sensor to be set. Select
“Suspend”, “Pause”, or “Off” for each sensor.

• Note that a program may not have both Pause and

Suspend responses. A program cannot be in both
Pause and Suspend at the same time. The responses
will automatically change to agree with the most
recent selection. If you set S1 to Pause, and then set
S2 to Suspend, the S1 will automatically change to
Suspend. It is impossible for a program to be in Pause
and Suspend at the same time.

• Once the sensor decoders are configured, the

controller will immediately begin polling the sensor
decoder continuously to monitor the alarms. This may
cause alarm messages until the sensor decoders are
actually installed in the two-wire path. The polling
function can be stopped to prevent false alarms.

See

Other Special Decoder Functions (Advanced Features)

on page 62 for more information.

oTher speCIal deCoder funCTIons (adVanCed feaTures) ......

VIeW DeCODer COnfIG

This allows the controller to search down the two-wire
path and return the configuration of any installed decoder
with an address. It can be used to determine whether
a particular station belongs to a 1, 2, 4, or 6 station
configuration, and can be used to retrieve the setup info
for a specified Sensor Decoder.

•

• Turn the Dial to Advanced Features. Arrow down to

"Decoder Functions." Press the + button.

• Arrow down to "View Decoder Config."

Press the + button.

• This is a view-only screen and cannot be used to edit

the decoder.

«
...
67
68
69
70
71
...
»

Содержание ACC-1200





































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-1200

Бренд: Yudian Страницы: 26

Бренд: CORNING Страницы: 142

Бренд: Combi Страницы: 28

Бренд: Argo-Hytos Страницы: 38

Бренд: Anest Iwata Страницы: 8

Бренд: Jeckson Electric Страницы: 2

Бренд: Continental Instruments Страницы: 2

Бренд: Viper Страницы: 2

Atlas V2 Stripe

Бренд: OBaby Страницы: 8

Бренд: Ebyte Страницы: 18

Бренд: QSC Страницы: 13

Бренд: Kaelus Страницы: 52

Бренд: Balboa Страницы: 2

Keystation 61es

Бренд: M-Audio Страницы: 15

Home Easy HE-414

Бренд: Byron Страницы: 2

Бренд: Airone Страницы: 2

Бренд: Dataprobe Страницы: 2

Amplifier MDM-7

Бренд: Danaher Motion Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды