Hunter Douglas Silhouette DuoLite Скачать руководство пользователя страница 12

Страница: 12 / 44

INSTALLATION

STEP 3: Install the Shading

Install the Optional Back Cover (If Applicable)

The optional back cover is used on inside mounts only.

■

Install the back cover into the back cover brackets on the rear of the installation brackets,
as shown. If necessary, trim the back cover to the desired width.

➤

For PowerView

and SoftTouch

™

Only:

n shadings with battery wand(s), the top

of the back cover fits onto the top tab of the back cover bracket.

IMPORTANT:

If using a battery wand, do not install the optional back cover until the

wand is installed. Refer to “STEP 2: Mount the Battery Wand, If Applicable” on
page 8.

IMPORTANT:

The back cover is not available with the rechargeable battery wand.

➤

On all other shadings, the top tab has been removed and installs closer to the
installation bracket.

Mount the Headrail

■

Peel back the protective covering from the top of the Palette

fabric-covered headrail.

Leave the rest of the protective covering on the front of the headrail.

■

Position the shading so that the front faces you.

■

Slide the headrail into the installation brackets so the edge of the headrail is between the
lever and the bracket, as shown.

■

Firmly push the headrail into each
bracket until it clicks and the lever
snaps to the right side of the bracket.

IMPORTANT:

Carefully pull on the

headrail at each bracket to ensure it
is installed securely.

■

Completely remove the protective covering from the Palette fabric-covered headrail.

Headrail

Installation

Bracket

Lever

Slide the Headrail

Between the Lever

and the Bracket

Back

Cover

Back

Cover

Shading with

Battery Wand

All Other Shadings

Содержание Silhouette DuoLite













































Результаты поиска

Содержание Silhouette DuoLite

Отзывы:

Похожие инструкции для Silhouette DuoLite

Бренды по названию

Популярные бренды

Hunter Douglas Silhouette DuoLite, Установка Эксплуатация Уход

Результаты поиска

Содержание Silhouette DuoLite

Отзывы:

Похожие инструкции для Silhouette DuoLite

Бренды по названию

Популярные бренды