Humminbird SC 110 Autopilot Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 63

Humminbird SC 110 Autopilot Скачать руководство пользователя страница 24

4.

Compass Settings

The autopilot system is compatible with a variety of compass
models. See the CPU installation guide for details. To enable each
compass in the Installation mode menu, use the guidelines in the
table below.

One heading sensor can be used at a time. To switch between the
magnetic compass and the GyroCompass, see

Manage Control

Head Settings: Switch the Active Compass

.

NOTE:

There are additional steps to conﬁgure the
compass with the Autopilot control head. See

Test the Autopilot and Finalize Installation

for

details.

Compass Model

Confirm Installation Mode Settings

Humminbird® FXC 110

and

Gyronav® rate sensor

Magnetic Compass Type

= FXC110

Gyronav

= Enabled

Humminbird® HRS1

Magnetic Compass Type

= HRS1

GyroCompass

(optional-purchase
expansion card required)

Expansion Card – GyroCompass Type

=

enter the appropriate value (see
GyroCompass installation guide)

18

Control Head Conﬁguration

«
...
22
23
24
25
26
...
»

Содержание SC 110 Autopilot
































































Отзывы:

Нет отзывов