Humminbird SC 110 Autopilot Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 63

Humminbird SC 110 Autopilot Скачать руководство пользователя страница 16

2.

Input Installation Settings

There are several installation settings available for the autopilot,
and the default settings are suitable for many vessels. Each menu
setting is important and must be accurate for maximum autopilot
performance.

•

Connected Equipment:

It is important to enable

devices that are connected to the autopilot control
head and CPU, such as the compass, rudder system,
and attached accessories.

•

Compass Models:

For more information about how to

enable various compass types, see

Section 4,

Compass Settings

.

•

Alarms:

Set the Rudder Alarm or the Oﬀ Course Time

Out in the Installation Mode.

•

Expansion Cards:

When an expansion card is installed

in the CPU, the corresponding settings will be added to
the Installation Mode menu, and you must enable
additional attached equipment (such as a
GyroCompass).

Setting Installation Menus

Number of

available

menus

and the

order in

the queue

Installation

Mode

Current

Menu

Menu Setting:
Turn Rotary Knob or press ARROW
keys to change settings.

10

Control Head Conﬁguration

«
...
14
15
16
17
18
...
»

Содержание SC 110 Autopilot
































































Отзывы:

Нет отзывов