Humminbird SC 110 Autopilot Скачать руководство пользователя страница 59

Страница: 59 / 63

Icon Alarm

Text

Description

Solution

No Compass

Compass signal lost Check compass installation

and connection to the CPU.

No Gyrocompass

Gyrocompass signal
lost

Check compass and
Gyrocompass installation
and connection to the CPU.

No Gyronav

Gyronav signal lost

Check Gyronav installation
and connection to the CPU.

Compass Error

Magnetic
Interference

Increase the distance
between the Gyrocompass
and other electromagnetic
devices.

Tiller Failure

Tiller failure on the
remote control

Off Course

The vessel has
traveled off course
from the set route
or heading.

Possible compass
interference. Increase the
distance between the
compass and other
electromagnetic devices.
Check compass installation
and connection to the CPU.

No Wind Input

Wind sensor input
lost

Check wind sensor
installation and connection
to the CPU. See the Wind
Sensor manual.

No GPS Input

Lack of GPS signal,
GPS has not
calculated the
position, or the data
transmission to the
autopilot has been
deactivated.

See the GPS manual to
review troubleshooting.
Check GPS installation and
connection to CPU.

Contact our Customer
Resource Center. There
may be keys failure or water
inside the remote control.

No Rudder
Feedback

Rudder feedback
signal not received.

Contact an authorized
technician (CMET or MEI)
or our Customer Resource
Center.

Alarms

Содержание SC 110 Autopilot
































































Результаты поиска

Содержание SC 110 Autopilot

Отзывы:

Похожие инструкции для SC 110 Autopilot

Бренды по названию

Популярные бренды

Humminbird SC 110 Autopilot, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SC 110 Autopilot

Отзывы:

Похожие инструкции для SC 110 Autopilot

Бренды по названию

Популярные бренды