manualshive.com logo in svg

Humboldt HM-5470.3F ConMatic IPC, Руководство по эксплуатации продукта

Поделиться
Скачать
Humboldt HM-5470.3F ConMatic IPC Скачать руководство пользователя страница 9

QUICK ST

AR

T GUIDE

9

Calibration Input Screen, cont.

Each channel has a “Limits On” check box (1). Use the Limits 

On to keep the machine from exceeding the sensor limits of 

the instrumentation. By selecting this option, before the test 

can exceed the limits of the sensors, all tests will stop run-

ning and the motor will stop to avoid damaging connected 

instrumentation.

Note: An input cannot be calibrated during testing.
Units (2)

In this field, a calibrated instrument will display the units 

that were chosen for use at the time of calibration. This field 

can also be used to automatically toggle conversion of units 

between lb.-in. and SI units if the need arises.

Value (3)

This field displays the current calibration value. This value 

should already be set with 4 decimal point accuracy 

(1)

 

below. If the instrument is not calibrated, the unit will read 

“N/A.”

1

2

3

4

1

Содержание HM-5470.3F ConMatic IPC

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды