Humboldt HM-5470.3F ConMatic IPC Скачать руководство пользователя страница 53

Страница: 53 / 56

HM-5470.3F Specifications

The HM-5470.3F ConMatic IPC is a fully-automated, incremental

pressure controller for performing incremental consolidation and

one-dimensional swell tests. The ConMatic IPC allows consolidation,

constant load and volume swell tests to be run automatically, freeing

up technicians for other tasks and reducing the duration of the testing

procedures by more than half—effectively saving time and manpower

and increasing lab profitability. One ConMatic automated system

can replace the production of several manual machines— running

incremental consolidation tests according to ASTM D2435 Method

B, where successive load increments are applied after 100% primary

consolidation.
Once a sample has been placed onto the test platform and the test

conditions set, the ConMatic IPC performs all consolidation tests,

including moving to the next stress level, without operator assistance.

The system automatically moves through the different test parameters

specified by the user with incremental consolidation tests typically

being completed in 24 to 48 hours. The Humboldt NEXT software uses

sample deformation readings taken from the displacement transducer

and load readings from the load cell to maintain a constant applied

stress or strain to the sample through the use of an accurate stepper

motor. Test results are recorded and rendered in real-time on the com-

puter screen while test data is stored and calculations are performed

automatically. The Humboldt NEXT software provides:

• Live tests and live graphing capabilities (real-time)
• Complete test reporting including all calculations and graphs required

for testing

• Review and exporting of tests using Microsoft Excel
• Smart Test Function: automatically picks up where it left off if the test

was not finished due to unexpected events within your computer

The unique design of the ConMatic IPC system enables the user to

connect multiple Conmatic IPC units to a single computer and run them

independently and simultaneously.

Содержание HM-5470.3F ConMatic IPC

























































Результаты поиска

Содержание HM-5470.3F ConMatic IPC

Отзывы:

Бренды по названию

Популярные бренды

Humboldt HM-5470.3F ConMatic IPC, Руководство по эксплуатации продукта

Результаты поиска

Содержание HM-5470.3F ConMatic IPC

Отзывы:

Бренды по названию

Популярные бренды