Humboldt HM-5470.3F ConMatic IPC Скачать руководство пользователя страница 4

Страница: 4 / 56

QUICK ST

T GUIDE

Unpacking

Initial inspection should include checking for physical dam-

age during shipping and obvious external damage to the

product.
Package contents are defined by your packing list. Each

Loader is configured according to customer specifications.

In your inspection, make certain that the contents of your

shipment match the documentation provided by your pack-

ing list.
Place unit on a flat, smooth surface and use leveling feet

(supplied) and use a bubble level to ensure that the unit is

level side-to-side and back-to-front.

Installation and Equipment Setup

Electrical Connections

The HM-5470 is equipped with an internal digital switching

power supply, which allows it to be used with most power

configurations throughout the world. The unit is supplied

with an IEC electrical cord with a standard 110V plug.
The HM-5470 arrives ready for operation. Attach the sup-

plied IEC electrical cord to the machine and plug into a

standard wall receptacle for use in the United States. For

locations other than the U.S., replace the supplied electrical

cord with an IEC cord that has the correct plug for your ap-

plication. The supplied cord can also be used by cutting the

standard plug from the cord and attaching the correct plug.

Power Switch

The Power Switch is located on the upper right hand corner

of the back of the machine, above the electrical cord inlet.

The Fuse Compartment is located between the electrical

cord inlet and the Power Switch. The HM-5470 uses a 10

amp fuse. To begin operation, attach the supplied electrical

cord, plug it in and press the Power Switch.

Fig. 1 Power Switch

Fuse Compartment

Содержание HM-5470.3F ConMatic IPC

























































Результаты поиска

Содержание HM-5470.3F ConMatic IPC

Отзывы:

Бренды по названию

Популярные бренды

Humboldt HM-5470.3F ConMatic IPC, Руководство по эксплуатации продукта

Результаты поиска

Содержание HM-5470.3F ConMatic IPC

Отзывы:

Бренды по названию

Популярные бренды