manualshive.com logo in svg

Hubner AMP 41, Инструкция по эксплуатации и сборке

Поделиться
Скачать
Hubner AMP 41 Скачать руководство пользователя страница 18

 

18 

AMP(H)41_MANUAL-en_R11 - 2019-03-28  

 

Absolute Encoder AMP(H) 41 

 

2.9 

 

Safety information 

 

 

 

WARNING! NOTICE! NOTES! 

Destruction, damage and malfunction of the measuring system! 

– 

Only carry out wiring work or opening and closing of electrical connections 
with the system de-energized. 

– 

Do not undertake any welding work if the measuring system is already wired 
or switched on. 

– 

Falling below or exceeding the permissible operating temperature limit values 
must be prevented through an appropriate heating/cooling measure at the 
place of installation. 

– 

The measuring system must be installed so that no direct moisture can affect 
the measuring system. 

– 

Suitable aeration/ventilation and heating/cooling measures must be provided 
at the place of installation to prevent the temperature falling below the dew 
point (condensation). 

– 

If an overvoltage of >36 V DC is inadvertently applied the measuring system 
must be inspected in the factory of Johannes Hübner - Fabrik elektrischer 
Maschinen GmbH, with specification of the reasons or circumstances. 

– 

Potential hazards resulting from interactions with other systems and equip-
ment which are or will be installed in the vicinity must be checked. The user is 
responsible for taking appropriate measures. 

– 

The power supply must be protected with a fuse suitable for the supply lead 
cross-section. 

– 

Cables used must be suitable for the temperature range. 

– 

A defective measuring system must not be operated. 

– 

Make sure that the installation environment is protected from aggressive me-
dia (acids etc.). 

– 

Avoid shocks (e.g. hammer blows) to the shaft during installation. 

– 

Opening the measuring system is forbidden. 

– 

Make sure that the access to the address switches and LEDs is locked after 
the settings with the screw plug. Tighten firmly! 

– 

The type plate specifies the technical characteristics of the measuring system. 
If the type plate is no longer legible or if the type plate is completely missing, 
the measuring system must not be operated. 

– 

In case of storage as well as in the operation of the measuring system unused 
connecting plugs have to be provided either with a mating connector or with a 
protective cap. The IP protection class is to be selected according to the re-
quirements. 

 

 

NOTES! 

The measuring system contains components and assemblies susceptible 
to electrical discharge, which can be destroyed if incorrectly handled. 
–

 

Touching the measuring system connection contacts with the fingers must be 
avoided or the relevant ESD protective measures must be applied. 

 

 

NOTES! 

Disposal 
–

 

If disposal has to be undertaken after the lifespan of the device, the respec-
tive applicable country-specific regulations are to be observed. 

Содержание AMP 41











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды