manualshive.com logo in svg

Huawei V100R021C00, Руководство пользователя

Поделиться
Скачать
Huawei V100R021C00 Скачать руководство пользователя страница 50

3.3.2 Application Conditions

Operating Environment

Table 3-11 Operating environment

Item

Specifications

Indoor unit

operating

temperature

0–40°C

Indoor unit

operating humidity

5%–95% RH (non-condensing)

Outdoor unit

operating

temperature

For high-temperature outdoor units: –10°C to +55°C
For normal-temperature outdoor units: –20°C to +45°C
For low-temperature outdoor units: –40°C to +45°C

Storage

temperature

Without refrigerant: –40°C to +70°C
With refrigerant: –40°C to +55°C

Storage humidity

5%–95% RH (non-condensing)

Altitude

1000–4000 m. The performance of the smart cooling

product is derated when the altitude ranges from 1000 m

to 4000 m. The maximum outdoor operating temperature

decreases 1°C and the nominal cooling capacity decreases

by 1% for each additional 200 m.

 

Installation Requirements

Table 3-12 Installation requirements

Installation Mode

Rack-mounted

Vertical Difference

Between the Indoor

and Outdoor Units

● Outdoor unit placed higher than the indoor unit: ≤

30 m

● Indoor unit placed higher than the indoor unit: ≤ 8

m

Maximum Equivalent

Length of One-way

Pipe

80 m. If the length exceeds 80 m, contact Huawei

technical support.

Thermal Insulation

Foam Thickness

≥ 13 mm

FusionModule800 Smart Small Data Center

User Manual

3 System Architecture

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

38

Содержание V100R021C00





























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды