Huawei V100R021C00 Скачать руководство пользователя страница 274

Страница: 274 / 508

Parameter

Smart Cooling Product No.

Rotation time The

parameter

can be set by

the hour

ranging from

midnight to

23:00 as

required.

Requirement

control

Competitive

running

avoidance

Step 4 After setting teamwork control parameters, choose Monitoring > Cooling >

NetCol5000-A1 > Running Info > Teamwork Information and check that the

displayed teamwork control information is consistent with the parameter settings.

NO TICE

If the information displayed under Teamwork Information is inconsistent with

the parameter settings, check the teamwork control cable connection and

teamwork control parameter settings.

----End

5.2.2.3 Setting the Maximum Outdoor Fan Speed

If the equipment room is near a noise-sensitive place, such as an office or a

meeting room, limit the rotational speed of the indoor fan within 80% to lower

the noise.

Procedure

Step 1 Choose Monitoring > Cooling > NetCol5000-A1 > Running Parameters > Indoor

Fan Parameters, set Max speed of indoor fan to 80%.

Step 2 Set Max speed of indoor fan to 80% of other smart cooling products in turn.

----End

5.2.3 Commissioning the Cooling System

Prerequisites

Check that the indoor and outdoor units have been powered on.

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

262

Содержание V100R021C00





























































































































































































































































































































































































































































































































Результаты поиска

Содержание V100R021C00

Отзывы:

Бренды по названию

Популярные бренды

Huawei V100R021C00, Руководство пользователя

Результаты поиска

Содержание V100R021C00

Отзывы:

Бренды по названию

Популярные бренды