manualshive.com logo in svg

Huawei V100R021C00, Руководство пользователя

Поделиться
Скачать
Huawei V100R021C00 Скачать руководство пользователя страница 433

c.

Tap the smart cooling product to be set in the cabinet layout diagram.

d. Choose Real-time Data > OFF.

●

Method 2: Log in to the ECC800-Pro WebUI as user admin. Choose

Monitoring > Cooling > NetCol5000-A1 > Controls > Control Information,

choose Startup/Shutdown control > OFF, and then click Submit.

NO TE

1 in NetCol5000-A1 is variable and subject to changes with the smart cooling product

connection sequence. The displayed value prevails.

Step 2 Disconnect the power supply from the smart cooling product control unit after the

smart cooling product shuts down over the EMS.

Step 3 Flip the clip on the PSU leftwards, as shown by (1) in 

Figure 6-18

.

Figure 6-18 Removing a PSU

Step 4 Take out the handle and pull out the PSU from the subrack, as shown by (2) in

Figure 6-18

.

Step 5 Insert the spare PSU into the corresponding slot, and flip the clip up to lock the

PSU.

Step 6 Start the smart cooling product over the EMS.

●

Method 1: Log in to the ECC800-Pro mobile phone or pad app as user admin.
a. Choose Home.
b. Tap the cabinet that houses the smart cooling product in the micro-

module view.

c.

Tap the smart cooling product to be set in the cabinet layout diagram.

d. Choose Real-time Data > ON.

●

Method 2: Log in to the ECC800-Pro WebUI as user admin. Choose

Monitoring > Cooling > NetCol5000-A1 > Controls > Control Information,

choose Startup/Shutdown control > ON, and then click Submit.

Step 7 Ensure that no alarm is generated for the smart cooling product after it runs for

30 minutes.

----End

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

421

Содержание V100R021C00





























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды