manualshive.com logo in svg

Huawei V100R021C00, Руководство пользователя

Поделиться
Скачать
Huawei V100R021C00 Скачать руководство пользователя страница 479

Figure 6-55 Installing a device

Step 4 Reconnect the cables to the new IVS1800.
Step 5 Turn on the power switch of the IVS1800.
Step 6 Commissioning the IVS1800. If the video recording function works properly after

commissioning, the IVS1800 is functional.

----End

6.4.4.9 Replacing a Hard Disk for the IVS1800

Prerequisites

●

A hard disk needs to be replaced.

●

Data in the hard disk has been backed up.

●

A spare hard disk of the same model is available and functional.

●

Before replacing a faulty disk, ensure that the power switch on the rear panel

is off and disconnect the power cable to power off the device.

Context

Recommended tools and materials: Phillips screwdriver, ESD wrist strap (or ESD

gloves).

Procedure

Step 1 Put on an ESD wrist strap (or ESD gloves) and insert the ground terminal into the

ESD jack in the cabinet.

Step 2 Remove the faulty hard disk.

1. Use a PH2 screwdriver to remove the two black screws on the rear of the

chassis cover, and take off the chassis cover.

Figure 6-56 Removing the chassis cover

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

467

Содержание V100R021C00





























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды