HTP MODCON500 FS страница 4 Скачать руководство пользователя

Страница: 4 / 66

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

Table of Contents

Part 1 - General Safety Information

A. Improper Combustion

B. Gas

C. When Servicing the Boiler

D. Boiler Water

E. Freeze Protection

F. High Elevation Installations

Part 2 - Before You Start

A. What’s in the Box

B. How the Boiler Operates

C. Optional Equipment

Part 3 - Prepare the Boiler

A. Locating the Boiler

B. Flooring

C. Leveling

D. Clearances for Service Access

E. Residential Garage and Closet Installations

F. Exhaust Vent and Intake Pipe

1. Direct Vent of Exhaust and Intake

2. Indoor Combustion Air in Confined or Unconfined Space

G. Carbon Monoxide Detectors

H. Prevent Combustion Air Contamination

I. Removing a Boiler from a Common Vent System

J. Water Chemistry Requirements*

K. Technical Specifications

Part 4 - Piping

A. General Plumbing Information

B. Relief Valve

C. Backflow Preventer

D. Expansion Tank

E. Circulators

F. Hydronic Piping with Circulators, Zone Valves, and Multiple Boilers

G. Circulator Sizing

H. Check / Control Water Chemistry

I. Plumbing

J. Fill and Purge Heating System

K. Freeze Protection Fluids

L. Zoning with Zone Valves

M. Zoning with Circulators

N. Multiple Boilers

O. Applications*

Part 5 - Venting

A. General

B. Approved Materials for Exhaust Vent and Intake Pipe

C. Additional Requirements for Installation in Canada

D. Exhaust Vent and Intake Pipe Location

E. Exhaust Vent and Intake Pipe Sizing

F. Longer Vent Runs

G. Exhaust Vent and Intake Pipe Installation

H. Applications

1. Direct Vent Installation of Exhaust and Intake

2. Room and Indoor Combustion Ventilation Requirements

Part 6 - Condensate Removal

Part 7 - Wiring

A. Installation Must Comply With

B. Field Wiring Terminations

The CSD-1 ASME Code, Section CW-400 requires that hot water

heating and supply boilers have a) a UL 353 temperature control

device, b) at least one (1) temperature-actuated control to shut

off the fuel supply when system water reaches a preset operating

temperature, c) a high temperature limit control that prevents

the water temperature from exceeding the maximum allowable

temperature by causing a safety shutdown and lockout, and d) its

own sensing element and operating switch.

The temperature control system integrated into the 926 control

provided with this heating appliance complies with the requirements

of CSD-1 Section CW-400 as a temperature operation control. The

control monitors the temperature difference between the inlet

and the outlet sensor, which is affected by boiler water flow. If this

temperature difference exceeds 55°F (typically because of low water

flow or very low heat load), the control will reduce the maximum fan

speed. If the temperature difference exceeds 60°F, the control will

effectively sense there is little or no water flow or heat load and shut

the boiler down. The controller will restart automatically once the

temperature difference has dropped below 55°F and the minimum

off time (anti-cycle time) has expired. In addition, if the control

senses that the outlet water temperature has reached 210°F, the

boiler is put into a hard lockout and requires manual reset to restart.

The hydronic supply and return connections of these products

are for installation in closed loop systems ONLY!

Use of this

product in any manner other than described in this manual may

result in premature product failure, substantial property damage,

severe personal injury, or death. Damage or failure of this product (or

the system in which it is installed) due to unauthorized use

IS NOT

COVERED BY WARRANTY.

IMPORTANT

In accordance with Section 325 (f) (3) of the Energy Policy and

Conservation Act, HTP has provided this boiler with multiple

features designed to save energy by reducing the boiler water

temperature as heating load decreases.

These features include:

•

A modulating combustion system that adjusts firing rate

based on heat demand.

•

Adjustment of boiler set point based on inferred heat

load as determined by an outdoor sensor. The outdoor

sensor is supplied by HTP with this boiler.

•

This boiler does not include a standing pilot.

•

This boiler is designed and shipped to assure the highest

efficiency operation possible. Such high efficiency is

achieved by limiting heating circuit water temperature to

140°F when there is no anticipated heat load, based upon

the outdoor sensor and the Outdoor Reset Curve (sensor

response curve) in the boiler software.

•

This feature may be over-ridden as described below in

specific installations:

•

The boiler control is equipped with an outdoor sensor

override for use with building management systems or in

cascaded systems (for systems with total input of 300,000

BTU/hr or greater).

See statement below for an important notice on the use of the

override.

IMPORTANT

In accordance with Section 325 (f) (3) of the Energy Policy and

Conservation Act, this boiler is equipped with a feature that

saves energy by reducing the boiler water temperature as

the heating load decreases. This feature is equipped with an

override which is provided primarily to permit the use of an

external energy management system that serves the same

function. THIS OVERRIDE MUST NOT BE USED UNLESS AT LEAST

ONE OF THE FOLLOWING CONDITIONS IS TRUE:

•

An external energy management system is installed that

reduces the boiler water temperature as the heating load

decreases.

•

This boiler is not used for space heating.

•

This boiler is part of a modular or multiple boiler system

having a total input of 300,000 BTU/hr or greater.

•

This boiler is equipped with a tankless coil.

Содержание MODCON500 FS



































































Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды

HTP MODCON500 FS, Установка, Запуск, Обслуживание, Запчасти, Гарантия

Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды