HTP MODCON500 FS страница 33 Скачать руководство пользователя

Страница: 33 / 66

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

Figure 24 - Wiring Cascade System

Figure 25 - Cascade Termination Plug Detail

P. Cascade Master Pump and Sensor Wiring

1. Place the cascade master overlay sticker onto the field connection

board on the boiler designated as the cascade master.

2. Connect the system pump hot wire to the terminal marked SYS

PUMP.

3. Connect the system pump neutral to the BOILER NEUT terminal and

the pump ground wire to the BOILER GND terminal.

4. Connect a jumper wire from the 120 VOLT terminal to the SYS PUMP

PWR terminal.

5. Connect the boiler pump to the terminals marked BOILER HOT,

BOILER NEUT, and BOILER GND.

6. Connect the system pipe sensor to the terminals marked SYS

SENSOR.

7. Connect the outdoor sensor (if used) to the terminals marked

OUTDOOR SEN.

8. Connect the signal to start the system to the terminals marked

THERMOSTAT.

NOTE:

This signal can come from a room thermostat or a dry contact

closure. No power of any voltage should be fed into either of these

terminals.

NOTE:

Place the Cascade Master label (included in shipping envelope)

on top of the boiler designated Master.

Q. Cascade Follower Pump and Sensor Wiring

1. If it is desired to have the boiler control the boiler pump, connect

the boiler pump to the BOILER HOT, BOILER NEUT, and BOILER GND

terminals.

2. If you are using an indirect fired water tank connected directly to

the follower boiler, connect the pump for it to the DHW HOT, DHW

NEUT, and DHW GND terminals.

If desired, an alarm bell or light can be connected to the alarm

contacts of the follower boiler. The normally closed alarm contact

may be used to turn a device off if the boiler goes into lockout mode.

The alarm contacts are rated 5 amps at 120 VAC.

To connect an alarm device, connect the power for the device to

the ALARM COM terminal. Connect the alarm device hot wire to

the ALARM NO terminal. Connect the neutral or return of the alarm

device to the neutral or return of the power for the alarm device.

To connect a device that should be powered off during a boiler

lockout condition, follow the same instructions as above and use

the ALARM NC terminal rather than the ALARM NO terminal.

NOTE:

In a cascade system, the alarm output of the boiler addressed

as #1 will also be active if the master boiler has a lockout condition.

The alarm output of boilers addressed #2-7 will only sound if a

lockout condition occurs on that specific boiler.

Содержание MODCON500 FS



































































Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды

HTP MODCON500 FS, Установка, Запуск, Обслуживание, Запчасти, Гарантия

Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды