HTP MODCON500 FS страница 37 Скачать руководство пользователя

Страница: 37 / 66

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

C. Check Inlet Gas Pressure

The gas valve is equipped with an inlet gas pressure tap that can be

used to measure the gas pressure to the unit. To check gas pressure,

perform the steps listed below:

IMPORTANT!

Before you connect to the inlet pressure, shut off the

gas and electrical power to unit.

2. Loosen the pressure tap with a small screwdriver. Refer to Figures 29

and 30 for location.

3. Each unit is equipped with a needle valve that will accept a 5/16 ID

hose to connect to a digital manometer or liquid gauge to measure

incoming pressure from 0-35” w.c.

4. Turn on the gas and power up the unit.

5. Put the unit into manual test mode (details on test mode in Part 10).

In test mode, monitor pressure to assure it does not drop below 1 inch

from its idle reading. If gas pressure is out of range or pressure drop

is excessive, contact the gas utility, gas supplier, qualified installer, or

service agency to determine correct action that is needed to provide

proper gas pressure to the unit. If Gas Pressure is within normal range

proceed to Step 6.

6. Exit test mode, then turn power off and shut off gas supply at

the manual gas valve before disconnecting the hose from the gas

monitoring device. Tighten screw on the pressure tap and turn gas on.

Check for leaks with soapy solution. Bubbles will appear on the pipe to

indicate a leak is present.

Ensure the pressure tap screw is properly tightened to prevent gas

leaks. Failure to do so could cause substantial property damage,

severe personal injury, or death.

The gas piping must be sized for the proper flow and length of pipe

to avoid pressure drop. The gas meter and regulator must be properly

sized for the total gas load. If you experience a pressure drop greater

than 1” w.c. (.87 kPa), the meter, regulator or gas line may be undersized

or in need of service. You can attach a manometer to the incoming

gas drip leg after removing the cap. The gas pressure must remain

between 3.5” (.87 kPa) and 14” (3.5 kPa) during stand-by (static) mode

and while in operating (dynamic) mode.

If an in-line regulator is used, it must be a minimum of 10 feet from the

boiler. It is very important that the gas line is properly purged by the

gas supplier or utility. Failure to properly purge the lines, or improper

line sizing, will result in ignition failure. This problem is especially

DO NOT adjust or attempt to measure gas valve outlet pressure.

The gas valve is factory-set for the correct outlet pressure and

requires no field adjustment. Attempts by the installer to adjust or

measure the gas valve outlet pressure could result in damage to

the valve and cause substantial property damage, severe personal

injury, or death.

Do not do a gas conversion on this boiler without an officially

approved conversion kit and instructions supplied by HTP. Failure

to use a conversion kit when converting the boiler to fire on

Natural or Propane gas will result in extremely dangerous burner

operation, leading to fire, explosion, severe personal injury, or

death.

Strain on the gas valve and fittings may result in vibration,

premature component failure and gas leakage, and result in fire,

explosion, property damage, severe personal injury, or death.
Adjustments to the throttle screw or offset may only be made by

a qualified gas technician using a calibrated combustion analyzer

capable of measuring CO2 and CO. Failure to follow this instruction

could result in fire, explosion, property damage, severe personal

injury, or death.
Ensure that the high gas pressure regulator is as least 6 – 10

feet upstream of the appliance. Failure to do so could result in

substantial property damage, severe personal injury, or death.

Natural or LP Gas

Minimum Pressure

3.5” WC

Maximum Pressure

14”WC

Table 15 - Gas Pressure Requirements

Do not fire (operate) the boiler until all connections have been

completed and the heat exchanger is filled with water. Doing so

will damage the boiler and void the warranty.

noticeable in NEW LP installations and empty tank situations. This

situation can also occur when a utility company shuts off service to

an area to provide maintenance to their lines. This gas valve must not

be replaced with a conventional gas valve under any circumstances.

Содержание MODCON500 FS



































































Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды

HTP MODCON500 FS, Установка, Запуск, Обслуживание, Запчасти, Гарантия

Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды