HTP MODCON500 FS страница 22 Скачать руководство пользователя

Страница: 22 / 66

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

B. Approved Materials for Exhaust Vent and Intake Pipe

Table 9 - Approved Materials for Exhaust Vent and Intake Pipe

C. Additional Requirements for Installation in Canada

1. Installations must be made with a vent pipe system certified to

ULC-S636. IPEX is an approved vent manufacturer in Canada supplying

vent material listed to ULC-S636. Additionally, you may use AL29-4C

stainless steel venting to comply with Canadian requirements.

2. The first three (3) feet of vent pipe from the boiler flue outlet must be

readily accessible for visual inspection.

3. The components of the certified vent system must not be

interchanged with other vent systems or unlisted pipe / fittings.

DO NOT mix components from different venting systems without

proper adapters. The vent system could fail, causing leakage of

flue products into the living space. Use only the approved pipe

and fitting materials, and primer and cement specifically designed

for the material used, as listed in the above table. Failure to do so

could result in property damage, serious injury, or death.

High heat sources (generating heat 100

F / 37

C or greater, such

as boiler flue pipes, space heaters, etc.) may damage plastic

components of the boiler as well as plastic vent pipe materials.

Such damages ARE NOT covered by warranty. It is recommended

to keep a minimum clearance of 8” from high heat sources.

Observe heat source manufacturer instructions, as well as local,

state, provincial, and national codes, laws, regulations, and

ordinances when installing this boiler and related components

near high heat sources.

NOTE:

The use of double-wall vent or insulated material for the

combustion air intake pipe is recommended in cold climates to prevent

the condensation of airborne moisture in the incoming combustion

air.

You must not use “B” vent in an exhaust application. “B” vent is for

intake applications ONLY. Using “B” vent in an exhaust application

will result in serious injury or death.

•

The exhaust and intake components installed with this appliance must be used for near appliance piping BEFORE transitioning to

the approved materials listed above. DO NOT REMOVE these installed components. Doing so WILL VOID appliance warranty.

•

PVC / CPVC pipe and fittings of the same diameter are considered interchangeable.

•

The use of cellular core PVC (ASTM F891), cellular core CPVC, or Radel

(polyphenolsulfone) in non-metallic venting systems is

prohibited.

•

Covering non-metallic vent pipe and fittings with thermal insulation is prohibited.

•

DO NOT connect PVC/CPVC to Polypropylene without an approved vent connector.

•

Any transition to Polypropylene MUST be done in the vertical within five (5) feet of the appliance.

•

When installing AL29-4C vent piping, install a PVC-to-stainless adapter at the appliance vent connection, and at the termination

when using a PVC termination kit. DO NOT mix AL29-4C piping from different manufacturers unless using adapters specifically

designed for the purpose by the manufacturer.

•

A double wall vent or insulated material may be used when using stainless steel vent material in a freezing climate.

•

*ABS may be used for air intake applications ONLY. ABS is NOT PERMITTED for use in Canada.

•

Contact the venting material manufacturer if there is any question about the applicability of the proposed venting material.

Failure to follow these directions will result in substantial property damage, severe personal injury, or death.

Item

Material

Standards for Installation In:

United States

Canada

Pipe and Fittings Approved for Intake ONLY

ABS*

ANSI/ASTM D2661

Pipe Approved for

Intake OR Exhaust Vent

PVC Schedule 40/80

UL-1738 or ANSI/ASTM D1785

UL-1738 or ULC-S636

PVC-DWV Schedule 40/80

UL-1738 or ANSI/ASTM D2665

CPVC Schedule 40/80

UL-1738 or ANSI/ASTM F441

Polypropylene

UL-1738 or ULC-S636

Stainless Steel AL29-4C

Certified for Category IV and Direct Vent Appliance Venting

Pipe Fittings

PVC Schedule 40

UL-1738, ANSI/ASTM D2466

or D2665

UL-1738 or ULC-S636

PVC Schedule 80

UL-1738, ANSI/ASTM D2467

or D2665

CPVC Schedule 40

UL-1738 or ANSI/ASTM F438

CPVC Schedule 80

UL-1738 or ANSI/ASTM F439

Pipe Cement

ABS*

ANSI/ASTM D2235

PVC

ANSI/ASTM D2564

IPEX System 636 Cements and

Primers

CPVC

ANSI/ASTM F493

Pipe Primer

PVC / CPVC

ASTM F656

Содержание MODCON500 FS



































































Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды

HTP MODCON500 FS, Установка, Запуск, Обслуживание, Запчасти, Гарантия

Результаты поиска

Содержание MODCON500 FS

Отзывы:

Похожие инструкции для MODCON500 FS

Бренды по названию

Популярные бренды