HSM SP 5088 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 60

HSM SP 5088 Скачать руководство пользователя страница 9

07/2013

2.991.999.120_en

9

SP 5088

1.3

Notes on work safety

Please pay particular attention to the following notes on work safety:

– The SP 5088 shredder press combination has been safety-tested by an accredited test-

ing

station.

Nevertheless, incorrect operation and misuse can result in:

  • the health or life of the operator
  • the machine and other valuable equipment
  • the effi cient operation of the shredder

– The SP 5088 shredder press combination has been built with the most up-to-date tech-

nology. However, the machine can be dangerous if improperly used, even by trainedstaff,
or if used for purposes other than those for which it was designed.

– The operation of the shredder press combination is always subject to local safety and ac-

cident prevention regulations.

– The employer must observe and comply with the “minimum safety and health require-

mentsfor the use of work equipment by workers at work”. Machinery Directive 2009/104/
EC

– The shredder press combination may not be operated by anyone under 16 years of age.

– All those charged with installation, assembly, disassembly, start-up, operation, inspection,

maintenance or repair of the baling press must have fi rst read and fully understood the
entire operating manual, paying particular attention to the “Safety” section.

– The shredder press combination may only be operated, serviced and repaired by author-

ised, trained staff. These staff must have been given special instructions on any dangers
which may possibly arise.

– Areas of personal responsibility for installation, assembly, re-assembly, set-up, operation

and maintenance must be clearly defi ned and strictly adhered to, in order to avoid confu-
sion which might compromise safety.

– When carrying out installation, disassembly, re-assembly, maintenance, operation, adjust-

ment and maintenance work always observe the shut-down procedures described in the
operating manual. Never perform this kind of work on the machine unless it is fully shut
down.

– Before performing such tasks make sure the drives and additional mechanisms of the

baling press cannot be switched on unintentionally. Turn the main switch to the “0” posi-
tion and secure it. Pull out the power plug.

– Before starting the machine after repairs, make sure all protective devices are in place.

«
...
7
8
9
10
11
...
»

Содержание SP 5088





























































Отзывы:

Нет отзывов