manualshive.com logo in svg

HSM SP 5088, Руководство по эксплуатации, Страница: 10 / 60

Поделиться
Скачать
HSM SP 5088 Скачать руководство пользователя страница 10

10  

 

2.991.999.120_en

 07/2013

SP 5088

– Do not carry out any tasks which may endanger your safety while operating the machine.

– Any changes which take place and could impair safety should be reported immediately. 

Put the machine out of operation until the damage is rectifi  ed.

–  Always make sure the machine is in perfect condition before you switch it on.

– Make sure the area around the machine is clean and safe.

– Unauthorised modifi  cations and changes to the machine are strictly prohibited. Protec-

tive devices may not be removed or otherwise rendered inoperative.

– No work on the machine which is not part of its normal operation may be performed while 

the machine is still running.

– Never open doors and fl  aps before the machine has been shut down. Note the instruc-

tion plate.

– Test the protective measures installed after any electrical or repair work.

– No platforms or other raised surfaces may be placed near the shredder press combina-

tion if they encroach on the specifi  ed safety clearances.

– Connecting cables must be laid in such a way that they cannot be tripped over.

– Only persons with the appropriate skills and experience in hydraulics may carry out work 

on the hydraulic equipment.

– All lines, pipes and bolted joints must be regularly inspected for looseness, leaks and vis-

ible damage. Any damage must be repaired immediately. Escaping oil can cause fi re and 
injury

– Any parts of the system and hydraulic pressure lines that need to be opened must be de-

pressurised according to the assembly instructions before commencing repair work.

Содержание SP 5088





























































Отзывы:

Нет отзывов