HSM SP 5088 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 60

HSM SP 5088 Скачать руководство пользователя страница 11

07/2013

2.991.999.120_en

11

SP 5088

1.4 Proper

use

The

SP 5088

shredder press combination is intended solely for shredding and pressing

paper and cardboard. The robust cutting unit is unaffected by staples and paper clips and
is even suitable for the destruction of whole volumes of fi les and folders. Excluding other
types of materials.

Operating mode :
Above-mentioned material is fed to the shredder. The crushed material falls through the
outlet of the shredder chute directly into the shaft of the press. The pressing operation is
initiated by a light barrier in the shaft when a certain level is achieved. The pressing plate
moves forward and presses the pressed material in the conical interference channel,
wherein it is compressed. The Shredder continues to run during the pressing process.
Once the bale has reached a certain length, it must be strapped manually. Then can
again be further pressed.
Due to the continuous pressing process, the sprue end compact bales ejected onto a
pallet or in a Plastic sack.

Any other use is considered improper. The manufacturer accepts no liability for damage
resulting from improper use - the operator carries sole responsibility for such use.

Proper use also includes carrying out installation, assembly, disassembly, start-up, op-
eration
and maintenance work as prescribed by the manufacturer. The baling press may
only be operated, serviced and repaired by staff who are familiar with these regulations
and aware of the dangers.

The shredder press combination may only be operated by authorised, trained staff. Do
not carry out any tasks which may endanger your safety while operating the machine.

The relevant accident prevention regulations and any other generally recognised health
and safety standards must also be observed.

«
...
9
10
11
12
13
...
»

Содержание SP 5088





























































Отзывы:

Нет отзывов