HSM SP 5088 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 60

HSM SP 5088 Скачать руководство пользователя страница 8

8

2.991.999.120_en

07/2013

SP 5088

1 Safety

1.1

Notes on safety

1.1.1

"Work safety" symbol

This symbol marks all work safety notes in this Operating Manual which
endanger the health or life of people. Please pay attention to this symbol and
exercise particular care in such cases. Please also forward all work safety
notes to other users.
Apart from the instructions in this manual, you must also follow generally ap-
plicable safety and accident prevention regulations.

1.1.2 "Notice"

symbol

This symbol marks information in this manual which requires particular at-
tention so that guidelines, regulations, instructions and correct working
procedures are followed and damage to or ruin of the machine and/or other
equipment prevented.

1.2 Classifi cation of hazards

1.2.1 Danger

identifi es an immediate danger. If not avoided, it will result in death or severe
injuries (crippling).

1.2.2 Warning

identifi es a possibly dangerous situation. If not avoided, it could result in
death or severe injuries.

1.2.3 Caution

identifi es a possibly dangerous situation. If not avoided, it could result in light
or minor injuries. Is also used for warnings concerning damage to material.

«
...
6
7
8
9
10
...
»

Содержание SP 5088





























































Отзывы:

Нет отзывов