HSM SP 5088 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

HSM SP 5088 Скачать руководство пользователя страница 36

36

2.991.999.120_en

07/2013

SP 5088

4.3 Initial

start-up

– Open the inspection door on the hopper and check that the press chamber is clear, and re-

move any spare parts or supplies delivered with the machine

– Insert the CEE Plug into the socket on site.

– Activate the emergency stop control by pushing the switch bar away from the machine.

– Unlock the emergency stop on the press.

– Switch on the main switch of the press and the shredder.

•

After a self-test by the control, the

Indicator:

Manual mode

Norminal xxx Actual xxx

–

If the error number 1000 (= phase is absent) or 1010

(= counter-clockwise phase rotation) appear in the display -> call an electrician!

See also the “Malfunctions” section

Warning!

Faults in electrical components and supply cables may only be attended
to by qualifi ed electricians or HSM service engineers.

–

Close the control cabinet, before continuing to commission the machine.

–

Set the desired user language

–

Set the desired barrel length or number of strokes of the press cylinder

Factory set value: body length 500 mm / stroke rate depends on the material

«
...
34
35
36
37
38
...
»

Содержание SP 5088





























































Отзывы:

Нет отзывов