HSM SP 5088 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 60

HSM SP 5088 Скачать руководство пользователя страница 46

46

2.991.999.120_en

07/2013

SP 5088

4.10

Malfunctions of the shredder

4.10.1 Overload due to paper jam

•

“Overload” display (level 1 or level 2 – depending on the machine model)

lights up red.

•

The drive automatically runs in reverse for several seconds. Then the cutting unit

switches

off..

Caution!
The blade rollers can still cause injuries even while they are not running.
Do not reach into the cutting unit!
Protective gloves should be worn at all times.
Do not repetitively run the cutting unit backwards and forwards, for the
purpose of removing an obstruction. This will damage the shredder.

-

Remove the stack of paper.

-

Press the automatic button on the press

-

Press the start button and put less paper on the feed belt.

4.10.2 Electric motor overheats

•

“Overload” display (level 1 or level 2 – depending on the machine model)

fl ashes red.

•

The drive automatically switches off.

-

Let the motor cool down for 20–30 minutes.

-

Press the automatic button on the press

-

Press the start button.

4.10.3 Emergency stop activated

•

Display lights up red.

•

The baling press and shredder switch off.

-

Activate the emergency stop control by pulling the switch bar away from

the

machine.

-

Press the automatic button on the press

-

Press the start button.

«
...
44
45
46
47
48
...
»

Содержание SP 5088





























































Отзывы:

Нет отзывов