HPE Aruba 3810 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 456

background image

DEFAULT_VLAN | DHCP/Bootp 15.255.157.54 255.255.248.0 Yes Yes

VLAN2100 | Disabled

Configuring source MAC based ARP attack detection (ARP
throttle)

ARP throttle operation

Source-MAC based ARP attack detection (ARP throttle) protects the switch CPU from ARP attacks by enabling
restriction of the overall number of ARP packets the CPU receives from a given client. An ARP attack occurs
when the switch receives more ARP packets from the same source MAC address than allowed by the configured
threshold setting. ARP throttle uses a “remediation mode” to determine whether to simply monitor the frequency
of ARP packets or actually restrict the ARP packet traffic from a given client. In cases where a device in your
network is sending a large quantity of ARP packets for legitimate purposes, you can configure ARP throttling to
exclude that device from being monitored.

When enabled in the default configuration, ARP throttle:

• monitors incoming ARP packets and “blacklists” clients sending excessive ARP packets to the switch

• maintains a count of clients sending ARP packets to the switch

When configured to filter ARP packet traffic, ARP throttle monitors ARP packet traffic as described above, and
also drops ARP packets received from blacklisted clients.

Non-default ARP throttle settings persist when ARP throttle is disabled.

ip arp-throttle enable

This command enables or disables ARP throttle operation for monitoring or filtering of ARP packets received by
the switch from other devices. (Default: disabled.) Enabling ARP-throttling uses the currently configured settings
to immediately invoke ARP attack monitoring and (if configured), to filter ARP packet traffic from devices
transmitting excessive ARP packets.

Syntax

ip arp-throttle enable
no ip arp-throttle enable

Description

Enables ARP throttle operation. The

no

form of the command disables ARP throttle operation.

ip arp-throttle remediation-mode

Determines the disposition of ARP packets the switch receives.

Syntax

ip arp-throttle remediation-mode <monitor | filter>

When ARP throttle is enabled in

monitor

mode (the default), the switch does the following:

• Monitors ARP packet traffic received by the switch CPU.

• Assigns “blacklist” status to devices generating an excessive numbers of ARP packets within a five-second

period.

• Maintains a running total of the devices from which ARP packets are being received.

134

Aruba 3810 / 5400R Multicast and Routing Guide for ArubaOS-

Switch 16.08

«
...
132
133
134
135
136
...
»

Содержание Aruba 3810









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aruba 3810

EasySmart DGS-1100-08

Бренд: D-Link Страницы: 44

Бренд: pathway Страницы: 28

Бренд: GE Страницы: 302

Бренд: GAIM Страницы: 2

Бренд: IBM Страницы: 44

Бренд: Lantronix Страницы: 2

Бренд: Tecsis Страницы: 2

Бренд: K-Dyne Страницы: 10

Бренд: Inline Страницы: 26

EOC Master CD7944N

Бренд: Data Страницы: 18

SwitchMan USB-Combo SW2

Бренд: Raritan Страницы: 2

Бренд: SUCO Страницы: 2

Бренд: Comm-Tec Страницы: 48

Бренд: Lightwave Страницы: 53

Бренд: X-keys Страницы: 4

Бренд: senva Страницы: 2

EXT-HDMI-CAT5-844

Бренд: Gefen Страницы: 28

Бренд: DANLERS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды